1. In the DLS 5 Software, go to Tools and Select Flash Wizard
The T-Link’s white panel connector to the PC-Link header of the control panel. The black wire of the PC-Link cable is pin 1 on the Power864 PC5020 control panel PC-Link header. And the PC-Link header on the MAXSYS. PC4020 control panel will only accept the proper connection. 2.2 Remote Control The panel and the DLS software will control this. When using only a PC-Link connection to connect to the panel you would want to start off by creating the account. To do so we would want the DLS software open and be viewing the main start page From here we can click on the New Account button (1), go from the File menu and select New Account (2), or right click within the Start Page and select.
2. The Flash Wizard will open and give you a selection where you can choose COM Port, and select the file to be uploaded (Browse to a local file, or click Web to search on the DSC flash file FTP
- DSC Alarm Panel programming with DLS 5 software - Answered by a verified Electronics Technician We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.
- When using only a PC-Link connection to connect to the panel you would want to start off by creating the account. To do so we would want the DLS software open and be viewing the main start page From here we can click on the New Account button (1), go from the File menu and select New Account (2), or right click within the Start Page and select.
3. If you open the Web section, you will see the different firmware files available on the FTP
4. Double-click or press [ENTER] to select the file you would like to load
NOTE: When doing an upgrade of the modules attached to the panel it is recommended to complete the Bridge firmware grade first before completing the Bundle upgrade. Failure to do so can cause errors while completing the upgrade on the Bundle package.
5. After continuing, the Flash Wizard will show the current panel version details
6. Click Next to continue with the upgrade if these are correct
Dsc Pc Link Software Download
7. For the upgrade to continue, please make sure the PC-Link cable is correctly connected to the left-hand 4 pins on PC-Link 2
8. Option 5 must be enabled in section [382]
9. Option 7 must be enabled in section [401]
10. Appropriate connection for the upgrade is shown below
11. The PC-Link cable must be connected on PC-Link 2, and must be on the left 4 pins.
12. The circuit board of the PC-Link connector must face down toward the terminal strip, with the jack facing up
13. After continuing, you will see the current panel info, and the upgrade panel info
14. Click Next to start the firmware flash to the new version
![Link Link](/uploads/1/2/6/6/126657207/170527037.jpg)
15. The firmware will start being sent to the panel, with a progress bar status. The Next button will remained grayed out until the transfer is complete
16. Once the firmware has been sent to the device, the screen will change to show that the update is being loaded to the panel
17. After the firmware is sent, DLS will verify the flash file of the unit to make sure that it is showing the correct information
18. Once DLS verifies the firmware, it will show you a final screen with the new version information
19. From this point, you can click Finish if you are done with the upgrade, or Back to flash another unit/firmware. If you have loaded the panel firmware, you will now need to load the firmware bundle containing files for the HS2#### keypads and HSM2HOST
Dsc Pc Link Cable
Please Note: If your panel does not normally have a 3G2080/TL2803GR/TL280 on it, please remember to disable [382] opt 5 and [401] opt 7 to ensure you do not have a trouble on the panel after leaving the site
Retrieved from 'http://dlshelp.dsc.com/index.php?title=PowerSeries_Neo/PowerSeries_Pro_Local_Firmware_Upgrade&oldid=2841'
Engine Management Software
Link Engine Management's software package, PC Link*, allows real time configuration of all functions in your Link ECU. With features such as automated tuning, data log analysis and ECU firmware updates, PC Link is one of the most comprehensive tuning packages available on the market.
PC Link gives the tuner the ability to modify the ECU tuning software layout to suit their needs. A tabbed page system allows multiple pages of information to be arranged and quickly viewed.
All versions of PC Link are FREE to download.
*PC Link is only currently available to download for Windows based PC's, laptops and tablets.
Please ensure you download the version corresponding to your ECU (A G4+ ECU will require a G4+ version of PC Link) and read through the 'Help file' which provides a lot of useful information.